Dräger Polytron 7500 Скачать руководство пользователя страница 42

Страница: 42 / 72

The menu » Calibration «

Page 42 of 72 Pages

9023927 - 2nd edition - May 2007

— The message » Fresh-air calibration running « is displayed.

●

Expose the sensor to the ambient air (for some sensors, a zero gas such as N

must be used – see the information in the section “Zero point calibration / adjust-
ment” on page 39).
Afterwards:

— The values for the calibration gas are displayed, for example,:

The current value and the calibration gas concentration are now displayed.

The calibration operation depends on whether the selected calibration gas supports
so-called autostability.

—

Autostability is supported:

When the displayed value has stabilised:

●

Select » Calibrate « and press the »

« key.

—

Autostability is not supported:

The instrument evaluates the stability of the signal and automatically executes the
calibration procedure.

— The required value and the actual value are now displayed.

●

Disconnect the flow of calibration gas.

If these are correct as displayed:

●

Select » Accept value « and press the »

« key.

Cal. gas

: NF

Unit

: ppm

Concentr.

: 000025

Attention: There is a danger after the gas is removed that an alarm is given
on the central controller while the gas is returning to normal level!

Содержание Polytron 7500









































































Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды

Dräger Polytron 7500, Инструкция по эксплуатации

Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды