Dräger Polytron 7500 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 72

background image

9023927 - 2nd edition - May 2007

Page 5 of 72 Pages

Intended Use

Intended Use

Dräger

Polytron

®

7500

— For stationary, continuous monitoring of gas concentrations in the intake ambient

air, with built-in DrägerSensor

®

.

— The Polytron 7500 is available in four types:

— The measuring range may be selected, but it is dependent on the sensor installed.

— With 4 to 20 mA interface or HART

®

for connection to a suitable control unit.

— Optional: compatible with LON interface for connection to a suitable control unit.

_______________

® Polytron is a registered trademark of Dräger.

DrägerSensor is a registered trademark of Dräger.
HART is a registered trademark of HCF, Austin, Texas, USA

Type

Order No.

Polytron 7500

DrägerSensor

Dräger Polytron 7500 NF

3

0 to 50 ppm NF

3

(CAS 7783-54-2)

83 18 827

68 11 125

Dräger Polytron 7500 PFC
0 to 30 ppm C

5

F

8

(CAS 559-40-0)

0 to 30 ppm C

4

F

6

(CAS 685-63-2)

83 18 828

68 11 120

Dräger Polytron 7500 NF

3

LON

0 to 50 ppm NF

3

(CAS 7783-54-2)

83 18 829

68 11 125

Dräger Polytron 7500 PFC LON
0 to 30 ppm C

5

F

8

(CAS 559-40-0)

0 to 30 ppm C

4

F

6

(CAS 685-63-2)

83 18 830

68 11 120

Note:
Polytron 7500 cannot be used with DrägerSensors other than the above
listed. The corresponding DrägerSensor must be used to ensure that the unit
functions correctly.

ATTENTION! Explosion hazard!
Do not operate underground or in explosion-hazard areas!
The Polytron 7500 does not meet the standards for ﬂameprooﬁng and explo-
sion protection.

Not to be used for intake from explosion-hazard areas!
The concentration of ﬂammable substances in the intake air must be limited
to values below the LEL

(Lower Explosive Limit)!

The gas mixture may otherwise be ignited because of the high pyrolysis tem-
perature in the Polytron 7500.

Only suitable for use in buildings!

00

1

2392

7_1

.eps

«
...
3
4
5
6
7
...
»

Содержание Polytron 7500









































































Отзывы:

Нет отзывов

Похожие инструкции для Polytron 7500

Бренд: TA Страницы: 58

Бренд: Igema Страницы: 30

Бренд: z-laser Страницы: 62

Бренд: Yamaha Страницы: 3

Бренд: Omer Страницы: 2

Бренд: A&D Страницы: 74

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: E Instruments Страницы: 2

Бренд: Keithley Страницы: 32

Бренд: IFM Страницы: 2

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: +GF+ Страницы: 8

Бренд: Hanna Instruments Страницы: 2

Бренд: Victron energy Страницы: 46

PASPORT PS-2174

Бренд: PASCO Страницы: 4

Бренд: Unipro Страницы: 2

Бренд: Velleman Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды