Dr Robot WFS802g Скачать руководство пользователя страница 37

Страница: 37 / 38

Authentication

Select an authentication scheme (Open) from the drop down menu.

Encryption

Select the encryption type from the pull down menu. 128 bits is the default
encryption.

Encryption Key

Field is enabled when WEP is selected as the Security type. Enter the
Encryption Key in hexadecimal value

Advanced Settings

Data Rate

WFS802g permits the control of the transmission rate. Select the data rate
(in Mbps) from the pull down menu.

Radio Power
Management

Power management reduces the overall power consumption of the
WFS802g unit. Selecting Enable increases the response time.

VI.7.

OEM Pin Configuration

There are 11 configurable hardware pins on the WFS802g unit. For each pin, configure the pin
function, communication direction, and its activity level.

To configure the WFS802g’s OEM Configurable Pins:

1. Click Configurable Pins from the main menu to open the Configurable Pins window.

Figure VI.9 Configurable Pins Settings

Configure or modify the following fields for each pin:

Function

From the pull down menu, select the purpose of the specified
pin.

Содержание WFS802g







































Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды

Dr Robot WFS802g, Руководство пользователя

Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды