Dr Robot WFS802g Скачать руководство пользователя страница 35

Страница: 35 / 38

2. In the available fields, enter the following information:

Connect

Protocol

Protocol Select

UDP from the pull down menu.

Figure VI.7 UDP Connection Settings

Datagram Mode

Datagram Type

Configures remote IP or network broadcast address and the remote port.
Enter 01 for directed or broadcast UDP.

Accept Incoming

Select Yes to accept incoming UDP datagrams.

Endpoint Configuration

Local Port

Enter the local port number.

Remote Port

Enter the port number of the remote device.

Remote Host

Enter the IP address of the remote device.

Change Address
Table

Field enabled when Datagram Type is set to FD. Enter values between 1-255
to identify units on the local network of device servers.

VI.6.

WLAN Configuration

Without adequate protection, a wireless LAN is susceptible to access by unauthorized users. As
such, WFS802g includes the Wired Equivalent Privacy (WEP) encryption standard as an additional
means of security.

To configure the WFS802g’s WLAN settings:
1.

Select WLAN from the main menu to open the WLAN Settings window.

Содержание WFS802g







































Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды

Dr Robot WFS802g, Руководство пользователя

Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды