Dr Robot WFS802g Скачать руководство пользователя страница 22

Страница: 22 / 38

Find Network Name

Enter the name of the network in which the WFS802g unit resides. The current value is displayed in
parentheses.

Find network name (DRI_IBSS) ?

Enable Ad Hoc Network Creation

The current value is displayed in parentheses. By default, Ad Hoc network creation is enabled on
WFS802g.

Enable Ad Hoc network creation (Y) ?

Name (DRI_IBSS) ?

Country 0=US, 1=FR, 2=JP, 3=Other (0) ?

Channel (11) ?

Enter Y to enable Ad Hoc network creation and display configurable parameters:

1. At the Name prompt, enter the network name as text and hit Enter. The default name displays in
parentheses.

2. Select a Country by entering 0, 1, or 3. By default, 0 (United States) is selected. Press Enter.

3. At the Channel prompt, enter the WFS802g’s channel setting.

Security

As an additional security measure, enable WEP on the WFS802g. The current value is displayed in
parentheses. By default, WEP is disabled on WFS802g.

Security 0=none, 1=WEP (0) ?

Data Rate

WFS802g permits the control of the transmission rate. The default is a data rate up to 11Mbps. The
current value is displayed in parentheses.

Data rate, Only : 0=1, 1=2, 2=5.5, 3=11 Mbps or

Up to: 4=2, 5=5.5, 6=11 Mbps (6) ?

Power Management

Power management reduces the overall power consumption of the WFS802g unit. Enabling power
management increases the response time. The current value is displayed in parentheses.

Enable power management (N) ?

V.6.

Expert Settings

Note:

Change these settings via Telnet or serial connections only.

Содержание WFS802g







































Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды

Dr Robot WFS802g, Руководство пользователя

Результаты поиска

Содержание WFS802g

Отзывы:

Похожие инструкции для WFS802g

Бренды по названию

Популярные бренды