Doosan HP450WJD T3 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 130

background image

Maintenance

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

93

Compressor Oil Separator Element

Normally the separator element will not require periodic maintenance provided that the air and
oil filter elements are correctly maintained.

If, however, the element has to be replaced, then proceed as follows:

Removal

WARNING

!

Do not remove the filter(s) without first making sure that the machine is
stopped and the system has been completely relieved of all air pressure.
(Refer to STOPPING THE UNIT in the OPERATING INSTRUCTIONS
section of this manual).

Disconnect all hoses and tubes from the separator tank cover plate. Remove the drop-tube
from the separator tank cover plate and then remove the cover plate. Remove the separator
element.

Inspection

Examine the filter element. Examine all hoses and tubes, and replace if necessary.

Reassembly

Thoroughly clean the orifice/drop tube and filter gasket contact area before reassembly. Install
the new element.

WARNING

!

Do not remove the staple from the anti-static gasket on the separator
element since it serves to ground any possible static build-up. Do not use
gasket sealant since this will affect electrical conductance.

Reposition the cover plate, taking care not to damage the gasket, and replace the cover plate
screws tightening in a

criss-cross

pattern to the recommended torque

(

refer to the

TORQUE

SETTING TABLE

later in this section

).

Engage the adaptor in the cover plate with the drop-tube integral with the filter, reconnect all
hoses and tubes to the separator tank cover plate.

Replace the compressor oil (refer to

LUBRICATION

later in this section).

«
...
91
92
93
94
95
...
»

Содержание HP450WJD T3



































































































































Отзывы:

Нет отзывов

Похожие инструкции для HP450WJD T3

YCAS0250-0440 60 HZ

Бренд: York Страницы: 9

Бренд: Meec tools Страницы: 36

Бренд: Motomaster Страницы: 18

Бренд: Vinotemp Страницы: 16

Timeter PCS-414

Бренд: Allied Страницы: 7

Бренд: Sparmax Страницы: 2

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 17

Бренд: ASTA Страницы: 37

Бренд: Xiaomi Страницы: 207

Бренд: Bostitch Страницы: 10

Бренд: Parkside Страницы: 209

BOGE CM9 Series

Бренд: Kärcher Страницы: 264

Compressor Sequencer OEM

Бренд: KE2 Страницы: 40

Бренд: Parkside Страницы: 36

Бренд: Zombie REC Страницы: 44

Бренд: California Air Tools Страницы: 17

Бренд: Raider Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды