Doosan HP450WJD T3 Скачать руководство пользователя страница 40

Страница: 40 / 130

Operating & Maintenance Manual

General Arrangement

Book: 23252059 (08-2010) Rev B

Lubricating Oil Specification

LUBRICATING OIL SPECIFICATION

(for the specified ambient temperatures).

ABOVE -23°C(-9°F)

Recommended: Pro-Tec

Approved: SAE 10W, API CF-4/CG-4

BELOW -23°C(-9°F)

Mandatory: Ingersoll Rand Performance 500

Ingersoll Rand Pro-Tec

compressor fluid is factory-fitted, for use at all ambient temperatures

above -23°C(-9°F).

NOTE:

Warranty may be extended only by continuous use of Pro-Tec

and

Ingersoll Rand oil filters and separators.

No other oil/fluids are compatible with Pro-Tec

No other oils/fluids should be mixed with Pro-Tec

because the resulting mixture could cause

damage to the airend.

In the event that Pro-Tec

is not available and /or the end user needs to use an approved

single grade engine oil, the complete system including separator/receiver, cooler and
pipework must be flushed clear of the first fill fluid and new Ingersoll Rand oil filters installed.

When this has been completed, the following oils are approved:

a. for ambient temperatures above -23°C(-9°F), SAE 10W, API CF-4/CG-4

b. for ambient temperatures below -23°C(-9°F), Ingersoll Rand Performance 500

only.

Safety data sheets can be obtained on request from the lubricant supplier.

For temperatures outside the specified ambient range, consult your Portable Power
representative.

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Бренды по названию

Популярные бренды