manualshive.com logo in svg

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Doosan HP450WJD T3 Скачать руководство пользователя страница 24

Operating & Maintenance Manual

Noise Emission

24

Book: 23252059 (08-2010) Rev B

NOISE EMISSION CONTROL MAINTENANCE LOG

The Noise Control Act of 1972 (86 Stat. 1234) prohibits tampering with the noise control 
system of any compressor manufactured and sold under the above regulations, specifically 
the following acts or the causing thereof:

(1) The removal or rendering inoperative by any persons, other than for purposes of 
maintenance, repair, or replacement, of any device or element of design incorporated into any 
new compressor for the purpose of noise control prior to its sale or delivery to the ultimate 
purchaser or while it is in use; or (2) the use of the compressor after such device or element 
of design has been removed or rendered inoperative by any person.

Noise Emission Warranty

The manufacturer warrants to the ultimate purchaser and each subsequent purchaser that this 
air compressor was designed, built and equipped to conform at the time of sale to the first retail 
purchaser, with all applicable U.S. EPA Noise Control Regulations.

This warranty is not limited to any particular part, component, or system of the air compressor. 
Defects in the design, assembly or in any part, component, or system of the compressor 
which, at the time of sale to the first retail purchaser, caused noise emissions to exceed 
Federal Standards are covered by this warranty for the life of the air compressor. 
(40FR204.58-1).

COMPRESSOR MODEL

_________________________

SERIAL NO.

__________________________________

USER UNIT NO.

_______________________________

UNIT IDENTIFICATION

ENGINE MAKE & MODEL:

DEALER OR DISTRIBUTOR FROM
WHOM PURCHASED:

SERIAL NO:_________________

__________________________________

PURCHASER OR OWNER:__________

__________________________________

ADDRESS: ____________________

DATE PURCHASED:_______________

Содержание HP450WJD T3



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды