Doosan HP450WJD T3 Скачать руководство пользователя страница 55

Страница: 55 / 130

Operating Instructions

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

Engine

Engine Serial Number Plate

Each engine has a 13-digit engine serial number.

The engine's serial number plate is located on the right-hand side of cylinder block behind the
fuel filter.

Fuels, Lubricants and Coolant

Diesel Fuel

Consult your local fuel distributor for properties of the diesel fuel available in your area.

In general, diesel fuels are blended to satisfy the low temperature requirements of the
geographical area in which they are marketed.

Diesel fuels specified to EN 590 or ASTM D975 are recommended.

Required Fuel Properties

In all cases, the fuel must meet the following properties:

Cetane number of 45 minimum.

Cetane number greater than 50 is preferred, especially for

temperatures below -20°C (-4°F) or elevations above 1500 m (5000 ft).

Cold Filter Plugging Point

(CFPP) below the expected low temperature OR

Cloud Point

least 5°C (9°F) below the expected low temperature.

Fuel lubricity

should pass a minimum load level of 3100 grams as measured by ASTM D6078

or, maximum scar diameter of 0.45 mm as measured by ASTM D6079.

Sulfur Content:

•

Diesel fuel quality and fuel sulfur content must comply with all existing regulations for
the area in which the engine operates.

•

Sulfur content less than 0.05% (500 ppm) is preferred.

•

If diesel fuel with sulfur content greater than 0.05% (500 ppm) is used, crankcase oil
service intervals may be affected. (See recommendation for Diesel Engine Oil).

•

DO NOT use diesel fuel with sulfur content greater than 1.0%.

IMPORTANT: DO NOT mix used engine oil or any other type of lubricating oil

with diesel fuel.

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды