manualshive.com logo in svg

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Doosan HP450WJD T3 Скачать руководство пользователя страница 125

Options

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

125

Prior to Starting

Check the lubricator oil level and replenish as necessary.

Maintenance

Check the lubricator oil level and replenish as necessary.

Fault Finding

Options - Dual Pressure

Safety

WARNING

!

Any pneumatic equipment that is, or may be connected to the machine
must be suitable for use with at least the higher, rated pressure.

Operating instructions

Commissioning

Check that switch and solenoid are functioning correctly.

Switch handle up: Lower pressure selected

Switch handle right: Higher pressure selected

Starting and Use

Select higher pressure setting with valve handle (handle to right) and start machine normally.

If lower pressure is required then turn handle to up position.

Toggle between high and low pressure as required.

FAULT

CAUSE REMEDY

No oil flow.

Incorrect connection

Reverse the nylon tube 
connections to the 
lubricator.

Содержание HP450WJD T3



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды