Doosan HP450WJD T3 Скачать руководство пользователя страница 73

Страница: 73 / 130

Lubrication

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

Symptom

Problem

Solution

Low oil pressure

Low oil level.

Add oil

Improper type of oil.

Drain, fill crankcase with oil of proper
Viscosity and quality.

High oil consumption

Crankcase oil too light.

Use proper viscosity oil.

Oil leaks.

Check for leaks in lines, gaskets, and
drain plug.

Restricted crankcase vent tube.

Clean vent tube.

Defective turbocharger.

See your authorized servicing dealer.

Engine emits white
smoke

Improper type of fuel.

Use proper fuel.

Low engine temperature.

Warm up engine to normal operating
temperature.

Defective thermostat.

Remove and check thermostat.

Defective injection nozzles.

See your authorized servicing dealer.

Engine emits black or
gray exhaust smoke

Improper type of fuel.

Use proper fuel.

Clogged or dirty air cleaner.

Service air cleaner.

Engine overloaded.

Reduce load.

Injection nozzles dirty.

See your authorized servicing dealer.

Electronic fuel system problem

See your authorized servicing dealer.

Turbocharger not functioning.

See your authorized servicing dealer.

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды