Doosan HP450WJD T3 Скачать руководство пользователя страница 71

Страница: 71 / 130

Lubrication

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

Symptom

Problem

Solution

Engine cranks but will
not start

Incorrect starting procedure

Verify correct starting procedure.

No fuel.

Check fuel in tank.

Exhaust restricted.

Check and correct exhaust
restriction.

Fuel filter plugged or full of
water

Replace fuel filter or drain water from
filter.

Injection pump not getting fuel
or air in fuel system.

Check fuel flow at supply pump or
bleed system.

Engine hard to start or
will not start

Engine starting under load.

Disengage PTO

Improper starting procedure.

Review starting procedure.

No fuel.

Check fuel tank.

Air in fuel line.

Bleed fuel line.

Cold weather.

Use cold weather starting aids.

Slow starter speed.

See "Starter Cranks Slowly".

Crankcase oil too heavy.

Use oil of proper viscosity.

Improper type of fuel.

Consult fuel supplier; use proper type
fuel for operating conditions.

Water, dirt, or air in fuel system

Drain, flush, fill, and bleed system.

Clogged fuel filter.

Replace filter element.

Dirty or faulty injection nozzles.

Have authorized servicing dealer or
engine distributor check injectors.

Electronic fuel system problem
if equipped

See your distributor or servicing
dealer.

Engine knocks

Low engine oil level.

Add oil to engine crankcase.

Low coolant temperature.

Remove and check thermostat.

Engine overheating.

See "Engine Overheats".

Engine cold

Wrong or defective thermostat.
Remove and check thermostat.

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Бренды по названию

Популярные бренды