manualshive.com logo in svg

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию, Страница: 53 / 130

Поделиться
Скачать
Doosan HP450WJD T3 Скачать руководство пользователя страница 53

Operating Instructions

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

53

Push After Warm Up

NOTE: 

In order to allow the machine to start at a reduced load, a valve, which

is operated by a button located on the instrument panel, is incorporated in the
regulation system. (The valve automatically returns to the start position when
the machine is switched off and air pressure relieved from the system)

.

•

Allow the engine to reach its operating temperature-then press the button(7).

•

At this point in the operation of the machine it is safe to apply 

full load

 to the engine.

Dual Pressure when Fitted

Machines which operate in excess of 7 bar (100 psi) can optionally be fitted with a dual 
pressure switch inside the unit. This switch selects between 7 bar (100 psi) and the machine 
rated pressure, cfm remains nominally constant.

Starting and stopping are unaffected by the selection and during normal running the selector 
switch may be safely operated. Precaution must be taken to ensure that downstream 
equipment is rated to suit the available pressure.

The pressure gauge indicates which setting has been selected.

Stopping the Machine

•

Close the service valve.

•

Allow the machine to run unloaded for a short period of time to reduce the engine
temperature.

•

Turn the start switch to the 

0

 (off) position.

NOTE: 

As soon as the engine stops, the automatic blowdown valve will relieve

all pressure from the system.

If the automatic blowdown valve fails to operate, then pressure must be relieved from the 
system by means of the service valve(s).

CAUTION

!

Never allow the machine to stand idle with pressure in the system.

Emergency Stopping

In the event that the unit has to be stopped in an emergency. 

TURN THE KEY SWITCH 

LOCATED ON THE INSTRUMENT PANEL TO THE 0 (OFF) POSITION.

Содержание HP450WJD T3



































































































































Отзывы:

Нет отзывов