Doosan HP450WJD T3 Скачать руководство пользователя страница 52

Страница: 52 / 130

Operating & Maintenance Manual

Operating Instructions

Book: 23252059 (08-2010) Rev B

Starting the Machine

WARNING

Under no circumstances should volatile liquids such as Ether be used for
starting this machine.

All normal starting functions are incorporated in the key operated switch.

•

Turn the key switch to position

The engine fault and compressor fault lamps will

flash.

Wait to Start Lamp.

•

Turn the key switch to position

until the Wait To Start Lamp. (14) extinguishes.

•

Turn the key switch to crank position (3) (engine start position)

NOTE:

Position (2) not used on AWJD models.

•

Release to position (1) when engine starts. The engine will now be running at a
reduced speed.

At temperatures below 0°C or if there is difficulty starting first time:

•

Open the service valve fully, with no hose connected.

•

Complete starting sequence above.

•

Close service valve as soon as engine runs freely.

•

Do not allow machine to run for long periods with service valve open.

•

Allow the engine to reach operating temperature.

•

At this point in the operation of the machine, it is safe to apply full load to the engine.

NOTE:

Wear hearing protection at all times when the engine is started with the

service valve open and air is flowing from the valve

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды