manualshive.com logo in svg

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Doosan HP450WJD T3 Скачать руководство пользователя страница 21

Decals

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

21

This section pertains only to machines distributed within the United States.

WARNING

!

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED

Federal law prohibits the following acts or the causing thereof:

(1) The removal or rendering inoperative by any persons, other than for purposes of 
maintenance, repair, or replacement, of any device or element of design incorporated into any 
new compressor for the purpose of noise control prior to its sale or delivery to the ultimate 
purchaser or while it is in use; or (2) the use of the compressor after such device or element 
of design has been removed or rendered inoperative by any person.

Among those acts included in the prohibition against tampering are these:

1. Removal or rendering inoperative any of the following:

a. the engine exhaust system or parts thereof

b. the air intake system or parts thereof

c. enclosure or parts thereof

2. Removal of any of the following:

a. fan shroud

b. vibration mounts

c. sound absorption material

3. Operation of the compressor with any of the enclosure doors open.

Compressor Noise Emission Control Information

A. The removal or rendering inoperative, other than for the purpose of

maintenance, repair, or replacement of any noise control device or element of
design incorporated into this compressor in compliance with the noise control
act;

B. The use of this compressor after such device or element of design has been

removed or rendered inoperative.

NOTE: the above information applies only to units that are built in
compliance with the U.S. Environmental Protection Agency.

Portable Power reserves the right to make changes or add improvements without notice and 
without incurring any obligation to make such changes or add such improvements to products 
sold previously.

The Purchaser is urged to include the above provisions in any agreement for any resale of this 
compressor.

Содержание HP450WJD T3



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды