Doosan HP450WJD T3 Скачать руководство пользователя страница 11

Страница: 11 / 130

Foreword

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

This machine has been designed and supplied for use only in the following specified
conditions and applications:

•

Compression of normal ambient air containing no known or detectable additional
gases, vapors or particles.

•

Operation within the ambient temperature range specified in the

GENERAL

INFORMATION

section of this manual.

UNITS MANUFACTURED IN NORTH AMERICA: Generation of electricity at 120V (1ph) at 60
Hertz.

UNITS MANUFACTURED IN EUROPE: Generation of electricity not applicable.

The use of the machine in any of the situation types listed in table 1:–

a) Is not approved by Portable Power,

b) May impair the safety of users and other persons, and

c) May prejudice any claims made against Portable Power.

The company accepts no responsibility for errors in translation of this manual from the original
English version.

TABLE 1

Use of the machine to produce compressed air for:

a) direct human consumption

b) indirect human consumption, without suitable filtration and purity checks.

Use of the machine outside the ambient temperature range specified in the

GENERAL

INFORMATION SECTION

of this manual.

This machine is not intended and must not be used in potentially explosive atmospheres,
including situations where flammable gases or vapors may be present.

Use of the machine fitted with non Portable Power approved components/lubricants/ fluids.

Use of the machine with safety or control components missing or disabled.

Use of the machine for storage or transportation of materials inside or on the enclosure
except when contained within the toolbox.

GENERATOR

Use of the generator to supply load(s) greater than those specified.

Use of unsafe or unserviceable electrical equipment connected to the generator.

Use of electrical equipment:

(a) Having incorrect voltage and/or frequency ratings.

(b) Containing computer equipment and/or similar electronics.

Содержание HP450WJD T3



































































































































Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды

Doosan HP450WJD T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HP450WJD T3

Отзывы:

Похожие инструкции для HP450WJD T3

Бренды по названию

Популярные бренды