manualshive.com logo in svg

Dodge 2004 Neon SRT4, Руководство по диагностике

"Скачайте бесплатно диагностическое руководство для Dodge 2004 Neon SRT4 на manualshive.com. Найдите все необходимые инструкции и руководства по обслуживанию для вашего автомобиля прямо сейчас. Просто загрузите нужное руководство в формате PDF и будьте готовы к любым ремонтам и техобслуживаниям."

Поделиться
Скачать
background image

TABLE OF CONTENTS - Continued

P1694-BUS COMMUNICATION WITH ENGINE MODULE. . . . . . . . . . . . . . . . . . . . . .153
P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION . . . . . . . . . . . . . .154
P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION. . . . . . . . . . . . . . . .158
P1790-FAULT IMMEDIATELY AFTER SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
P1793-TRD LINK COMMUNICATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
P1794-SPEED SENSOR GROUND ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
P1797-MANUAL SHIFT OVERHEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
*BACKUP LAMPS COME ON WHILE SHIFTER IS NOT IN REVERSE POSITION. .168
*BACKUP LAMPS INOPERATIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
*CHECKING PARK/NEUTRAL SWITCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . .171
*NO MANUAL AUTOSTICK OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
*PRNDL FAULT CLEARING PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
*TRANSMISSION NOISY WITH NO DTC’S PRESENT . . . . . . . . . . . . . . . . . . . . . . . .176
*TRANSMISSION SHIFTS EARLY WITH NO DTC’S . . . . . . . . . . . . . . . . . . . . . . . . . .177
*TRANSMISSION SIMULATOR 8333 WILL NOT POWER UP . . . . . . . . . . . . . . . . . .178

VERIFICATION TESTS
VERIFICATION TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179

8.0

COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181

8.1

AUTOSTICK - IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181

8.2

POWERTRAIN CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181

8.3

PRESSURE PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181

8.4

TRANSMISSION COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .182

9.0

CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

AUTOSTICK SWITCH - NATURAL 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
DATA LINK CONNECTOR - WHITE 16 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
FUSES (FB LHD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
FUSES (FB RHD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
INPUT SPEED SENSOR - GRAY 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
LEFT BACKUP LAMP - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
OUTPUT SPEED SENSOR - GRAY 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
FUSES (PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
TRANSMISSION CONTROL RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
POWERTRAIN CONTROL MODULE C1 - BLACK 38 WAY. . . . . . . . . . . . . . . . . . . . .191
POWERTRAIN CONTROL MODULE C2 (2.0L) - ORANGE 38 WAY . . . . . . . . . . . . .192
POWERTRAIN CONTROL MODULE C2 (2.4L TURBO) - GRAY 38 WAY . . . . . . . . .193
POWERTRAIN CONTROL MODULE C3 - WHITE 38 WAY. . . . . . . . . . . . . . . . . . . . .194
POWERTRAIN CONTROL MODULE C4 - GREEN 38 WAY . . . . . . . . . . . . . . . . . . . .195
RIGHT BACKUP LAMP - BLACK 2 WAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195
THROTTLE POSITION SENSOR (2.0L) - BLACK 3 WAY . . . . . . . . . . . . . . . . . . . . . .196
THROTTLE POSITION SENSOR (2.4L TURBO) - NATURAL 3 WAY . . . . . . . . . . . . .196
TRANSMISSION RANGE SENSOR - DK. GRAY 10 WAY . . . . . . . . . . . . . . . . . . . . . .196
TRANSMISSION SOLENOID/PRESSURE SWITCH ASSEMBLY - BLACK 8 WAY . .196

10.0

SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197

iii

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
JAC S5 Workshop Manual preview
S5
Бренд: JAC Страницы: 70
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Бренд: Wallbox Страницы: 7
GARO ENTITY PRO Installation preview
ENTITY PRO
Бренд: GARO Страницы: 2
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Бренд: Axxess Страницы: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Бренд: SeaSucker Страницы: 9
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Бренд: Voxoa Страницы: 48
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Бренд: Oldsmobile Страницы: 354
MAcarbon MAA.R8.06 Install Instructions preview
MAA.R8.06
Бренд: MAcarbon Страницы: 3
Dakota Digital CRS-3000-3 Manual preview
CRS-3000-3
Бренд: Dakota Digital Страницы: 20
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Бренд: Coolster Страницы: 45
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3
Scosche HAQ02 Quick Start Manual preview
HAQ02
Бренд: Scosche Страницы: 8
ideus vv900 User Manual preview
vv900
Бренд: ideus Страницы: 116
Skoda 2015 Superb Owner'S Manual preview
2015 Superb
Бренд: Skoda Страницы: 276
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Бренд: Connects2 Страницы: 2
Ratio Electric HOME BOX SMART Manual preview
HOME BOX SMART
Бренд: Ratio Electric Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды