Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 922

background image

TEST

ACTION

APPLICABILITY

3

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

4

NOTE: Ensure the battery is fully charged.
With the DRBIII

t

, record and erase all DTCs from all modules.

All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII

t

monitor active codes as you work through the system.

NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?

All

Yes

→

Select appropriate symptom from Symptom List.

No

→

No problem found at this time. Erase all codes before returning
vehicle to customer.

50

AIRBAG

NO CLUSTER MESSAGE —

Continued

«
...
55
56
57
58
59
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: kincrome Страницы: 6

Бренд: muth Страницы: 10

PRIME DESIGN VBI-FT21B

Бренд: Safe Fleet Страницы: 12

Plusone Console 4521011B

Бренд: Honda Страницы: 4

Бренд: tams elektronik Страницы: 19

Бренд: Hyundai Страницы: 19

Бренд: Thule Страницы: 12

Бренд: Volvo Страницы: 123

Бренд: Mercedes-Benz Страницы: 10

Powerbuilt 648601

Бренд: AllTrade Страницы: 3

SportQuest Series

Бренд: Perrycraft Страницы: 2

Бренд: Curt Group Страницы: 2

Бренд: Revelation Страницы: 4

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Бренд: Ecco Страницы: 2

Бренд: RADICAL Страницы: 11

Бренд: XTC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды