Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 922

background image

Verification Tests

40/41TE (NGC) TRANSMISSION VERIFICATION TEST - VER 1

APPLICABILITY

1. NOTE: After completion of the Transmission Verification Test, the Powertrain
Verification Test must be performed. Refer to the Powertrain Category.
2. Connect the DRBIII

t

to the Data Link Connector (DLC).

3. Reconnect any disconnected components.
4. With the DRBIII

t

, erase all Transmission DTC’s, also erase the PCM DTC’s.

5. Perform *PRNDL FAULT CLEARING PROCEDURE after completion of repairs for P0706
CHECK SHIFTER SIGNAL.
6. With the DRBIII

t

, display Transmission Temperature. Start and run the engine until the

Transmission Temperature is HOT, above 43° C or 110° F.
7. Check the transmission fluid and adjust if necessary. Refer to the Service Information for the
Fluid Fill procedure.
8. NOTE: If the Transmission Control Module or Torque Converter has been replaced,
or if the Transmission has been repaired or replaced, it is necessary to perform the
DRBIII

t

Quick Learn Procedure and reset the

(

Pinion Factor

(

.

9. Road test the vehicle. With the DRBIII

t

, monitor the engine RPM. Make 15 to 20 1-2, 2-3,

3-4 upshifts. Perform these shifts from a standing start to 45 MPH with a constant throttle
opening of 20 to 25 degrees.
10. Below 25 MPH, make 5 to 8 wide open throttle kickdowns to 1st gear. Allow at least 5
seconds each in 2nd and 3rd gear between each kickdown.
11. For a specific DTC, drive the vehicle to the Symptom’s When Monitored/When Set
conditions to verify the DTC is repaired.
12. If equipped with AutoStick

t

, upshift and downshift several times using the AutoStick

t

feature during the road test.
13. NOTE: Use the EATX OBDII task manager to run Good Trip time in each gear, this
will confirm the repair and to ensure that the DTC has not re-matured.
14. Check for Diagnostic Trouble Codes (DTC’s) during the road test. If a DTC sets during the
road test , return to the Symptom list and perform the appropriate symptom.
15. NOTE: Erase P0700 DTC in the PCM to turn the MIL light off after making
transmission repairs.
Were there any Diagnostic Trouble Codes set during the road test?

All

Yes

→

Repair is not complete, refer to the appropriate symptom.

No

→

Repair is complete.

235

VERIFICATION TESTS

«
...
240
241
242
243
244
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: iDataLink Страницы: 9

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Metra Electronics Страницы: 8

Бренд: Jeep Страницы: 16

Бренд: Audi Страницы: 4

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: Carcomm Страницы: 2

Бренд: Toyota Страницы: 285

Бренд: v.link Страницы: 19

Бренд: APS Страницы: 4

Бренд: SuperATV Страницы: 2

Бренд: Black Horse Off Road Страницы: 3

Бренд: Whispbar Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды