Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 314 | Manualshive

Страница: 314 / 922

background image

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the CAB harness connector.
Inspect the CAB and CAB harness connector for damage.
Is there any broken, bent, pushed out, corroded, or spread terminals?

All

Yes

→

Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the CAB harness connector.
Using a 12-volt test light connected to 12-volts, probe the Ground circuits.
Does the test light illuminate?

All

Yes

→

Go To

5

No

→

Repair the Ground circuit for an open.
Perform ABS VERIFICATION TEST - VER 1.

5

Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output (RUN) circuit.
Does the test light illuminate?

All

Yes

→

Replace the Controller Antilock Brake in accordance with the
Service Information.
Perform ABS VERIFICATION TEST - VER 1.

No

→

Repair the Fused Ignition Switch Output (RUN) circuit for an
open.
Perform ABS VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Refer to any Hotline letters or Technical Service Bulletins that may apply.
Ensure the battery is fully charged.
Inspect the vehicle for aftermarket accessories that may exceed the Generator
System output.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Were any problems found?

All

Yes

→

Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.

No

→

Test Complete.

32

BRAKES (CAB)

SYSTEM UNDER VOLTAGE —

Continued

«
...
312
313
314
315
316
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: Jeep Страницы: 25

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: GOgroove Страницы: 9

Бренд: Paxton Automotive Страницы: 85

Бренд: Thule Страницы: 8

Wireless Charging Station Universal

Бренд: BMW Страницы: 160

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: TATA Motors Страницы: 136

Бренд: Cadillac Страницы: 409

Бренд: Fortin Страницы: 9

Бренд: Hyundai Страницы: 11

Бренд: Motoalliance Страницы: 5

Бренд: Improved Racing Страницы: 17

TX-STAMP-4-FC04

Бренд: Over Armour Offroad Страницы: 9

Бренд: ECS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды