Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 802 | Manualshive

Страница: 802 / 922

background image

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t

, read Transmission DTC’s.

If any of these DTC’s are present, perform their respective tests first.
Are there any Loss of Prime, Line Pressure Sensor and/or Speed Sensor DTCs
present?

All

Yes

→

Refer to the Transmission category and perform the appropriate
symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

3

3

With the DRBIII

t

, perform the 4th gear clutch test. Follow the instructions on the

DRBIII

t

.

Increase the throttle angle or TPS Degree to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the clutch test pass - Input Speed remain at zero?

All

Yes

→

Go To

4

No

→

Go To

5

4

The conditions to set this DTC are not current at this time.
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC’s, check the
Speed Sensors for proper operation.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t

, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→

Repair as necessary.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Test Complete.

5

With the DRBIII

t

, read Transmission DTC’s.

Are the DTC’s P0870 and/or P0871 present also?

All

Yes

→

Replace the Solenoid/Pressure Switch Assembly per the Service
Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

6

81

TRANSMISSION - NGC

P0734-GEAR RATIO ERROR IN 4TH —

Continued

«
...
800
801
802
803
804
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: Vauxhall Страницы: 2

Бренд: Pivot Страницы: 4

NPL-TV 7874 DIGITAL

Бренд: Napoli Страницы: 20

Бренд: Prorack Страницы: 14

Бренд: FormFit Страницы: 4

Parrot MKi + ParrotCK3100 range LOGAN

Бренд: Parrot Страницы: 10

Бренд: rockymounts Страницы: 6

Бренд: GYS Страницы: 32

Бренд: PEUGEOT Страницы: 232

Бренд: Ultraplast Страницы: 5

Бренд: T-Tech Страницы: 1

Бренд: Yakima Страницы: 10

Бренд: Macally Страницы: 10

Бренд: Chevrolet Страницы: 376

Бренд: HawksHead Страницы: 10

6"OFF ROAD LIGHT 95811

Бренд: U.S. General Страницы: 7

Бренд: Tesla Страницы: 5

Бренд: Black & Decker Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды