Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 461 | Manualshive

Страница: 461 / 922

background image

TEST

ACTION

APPLICABILITY

5

Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Install a fuel pressure gauge.
Start the engine and observe the fuel pressure reading.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Choose a conclusion that best matches your fuel pressure reading.

All

Within Specification

Go To

6

Below Specification

Go To

12

Above Specification

Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

6

NOTE: Before continuing visually and physically inspect the fuel delivery
system for external leaks or damage. Repair /replace as necessary.
Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install special 5/16 fuel line adapter tool #6539.
Attach a fuel pressure test gauge to the T fitting on the tool #6539
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Using special tool #C4390, Hose Clamp Pliers, slowly clamp off the rubber hose on
the Fuel Pressure adapter between the fuel pressure gauge and the fuel pump
module.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi)
Does the fuel pressure gauge fall below the above specification?

All

Yes

→

Replace the leaking Injector(s).
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

7

7

Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
CAUTION: After each actuation of the Fuel Injector, start the engine to clear
the cylinder of fuel. Failure to do so could cause engine damage.
Install a Fuel Pressure Gauge to the fuel rail.
Start the engine and allow the fuel pressure to reach maximum pressure.
Turn the engine off, leaving the ignition on.
Using the DRBIII

t

, actuate the Fuel Injector for the cylinder that indicated the

misfire.
Monitor the fuel pressure gauge.
Does the fuel pressure gauge indicate a drop in fuel pressure?

All

Yes

→

Go To

8

No

→

Go To

9

125

DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE —

Continued

«
...
459
460
461
462
463
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: TATA Motors Страницы: 94

Бренд: GÄN Страницы: 24

Бренд: Velleman Страницы: 6

Бренд: Phonocar Страницы: 2

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: Boyo Страницы: 9

Бренд: U.S. General Страницы: 8

Бренд: Radical Sportscars Страницы: 44

Бренд: Jaeger Страницы: 11

Бренд: cam Страницы: 6

Бренд: Power Acoustik Страницы: 4

Interlock 700 Series

Бренд: Scania Страницы: 82

Бренд: Voxx Electronics Страницы: 15

Бренд: Roadmaster Страницы: 4

Бренд: TomTom Страницы: 22

Бренд: Saab Страницы: 498

Бренд: Menabo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды