Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 243 | Manualshive

Страница: 243 / 922

background image

ABS VERIFICATION TEST - VER 1

APPLICABILITY

1. Turn the ignition off.
2. Connect all previously disconnected components and connectors.
3. Ensure all accessories are turned off and the battery is fully charged.
4. Ensure that the Ignition is on, and with the DRBIII, erase all Diagnostic Trouble Codes from
ALL modules. Start the engine and allow it to run for 2 minutes and fully operate the system
that was malfunctioning.
5. Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRBIII, read
DTC’s from ALL modules.
6. If any Diagnostic Trouble Codes are present, return to Symptom list and troubleshoot new
or recurring symptom.
7. NOTE: For Sensor Signal and Pump Motor faults, the CAB must sense all 4 wheels
at 25 km/h (15 mph) before it will extinguish the ABS Indicator.
8. If there are no DTC’s present after turning ignition on, road test the vehicle for at least 5
minutes. Perform several antilock braking stops.
9. Caution: Ensure braking capability is available before road testing.
10. Again, with the DRBIII

t

read DTC’s. If any DTC’s are present, return to Symptom list.

11. If there are no Diagnostic Trouble Codes (DTC’s) present, and the customer’s concern can no
longer be duplicated, the repair is complete.
Are any DTC’s present or is the original concern still present?

All

Yes

→

Repair is not complete, refer to appropriate symptom.

No

→

Repair is complete.

AIRBAG VERIFICATION TEST - VER 1

APPLICABILITY

1. Remove any special tools or jumper wires and reconnect all previously disconnected
components - except the Battery.
2. WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNITION ON,
THEN RECONNECT THE BATTERY.
3. Connect the DRBIII

t

to the Data Link Connector - use the most current software available.

4. Use the DRBIII

t

and erase the stored codes in all airbag system modules.

5. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
6. Wait one minute, and read active codes and if there are none present read the stored codes.
7. Note: If equipped with Airbag On-Off switch, read the DTC’s in all switch positions.
8. Note: Read the DTC’s in all airbag system related modules.
9. If the DRBIII

t

shows any active or stored codes, return to the Symptom list and follow path

specified for that trouble code. If no active or stored codes are present, the repair is complete.
Are any DTC’s present or is the original condition still present?

All

YES

Repair is not complete, refer to appropriate symptom list.

NO

Repair is complete.

236

VERIFICATION TESTS

Verification Tests —

Continued

«
...
241
242
243
244
245
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Jeep Страницы: 25

Бренд: Carefree Страницы: 12

Бренд: DAVIS Страницы: 32

Бренд: FALCON RIDGE Страницы: 7

Бренд: Volvo Страницы: 30

Бренд: U.S. General Страницы: 8

Бренд: Gator Страницы: 8

Бренд: benbat Страницы: 14

Бренд: SPL Страницы: 5

Бренд: POOL-LINE Страницы: 2

Бренд: FORM FIT Страницы: 2

Бренд: HAKR Страницы: 9

Бренд: Hyundai Страницы: 168

Бренд: Blaupunkt Страницы: 6

Outlander Plug-in hybrid

Бренд: Mitsubishi Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды