Dodge 2004 Neon SRT4 Скачать руководство пользователя страница 466 | Manualshive

Страница: 466 / 922

background image

Symptom:

P0315-NO CRANK SENSOR LEARNED

When Monitored and Set Condition:

P0315-NO CRANK SENSOR LEARNED

When Monitored:

Under closed throttle decel and A/C off. ECT above 75°C (167°F).

Engine start time is greater than 50 seconds.

Set Condition:

One of the CKP sensor target windows has more than 2.86% variance from

the reference. One Trip Fault.

POSSIBLE CAUSES

DTC VERIFICATION

TONE WHEEL/PULSE RING INSPECTION

WIRING HARNESS INSPECTION

CRANKSHAFT POSITION SENSOR

TEST

ACTION

APPLICABILITY

1

NOTE: Check for any TSBs that may apply to this symptom.
Ignition on, engine not running.
With the DRBIII

t

, clear DTCs, and perform the PCM battery disconnect to reset the

PCM.
Start the engine.
If the MIL has not yet illuminated, test drive the vehicle to try to get the code to reset.
Does the code reset while cranking or during the test drive?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Visually inspect the CKP wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the CKP wire harness connectors. Look for broken, bent, pushed out,
or corroded terminals.
Ensure the Crankshaft Position Sensor is properly installed and the mounting bolt
tight.
Refer to any TSB that may apply.
Were any of the above conditions present?

All

Yes

→

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

130

DRIVEABILITY - NGC

«
...
464
465
466
467
468
...
»

Содержание 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 Neon SRT4

Бренд: Jabra Страницы: 10

Бренд: Porsche Страницы: 192

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

MILSCO KIT# C746700

Бренд: K&M Страницы: 2

Бренд: Car-Interface Страницы: 25

2 Bike Carrier 977

Бренд: Thule Страницы: 6

Бренд: Xblitz Страницы: 30

Бренд: METRON Страницы: 4

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: GMC Страницы: 430

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

Бренд: POOL-LINE Страницы: 2

Бренд: Honda Страницы: 253

Бренд: Toyota Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды