Docomo N-03A, Инструкция по эксплуатации

Страница: 398 / 506

396
Appe
ndix/T
roub
leshooti
ng
“Cannot use because of a different FOMA card
(UIM)”
●
This is displayed when you select and attempt to run a
desktop icon for data that is protected by FOMA card
security function. → P.36
●
This is displayed when you select and attempt to run a
screen memo or MessageR/F that is protected by
FOMA card (UIM) security function. → P.36
“Caution! A telephone number or URL is written
in this message. Be careful if you do not know the
sender”
●
This is displayed if Message Scan is turned on under
Scan functions and you are about to display an SMS
which contains a telephone number of URL in the text.
Check the sender, then press
d
to display the text of
the SMS.
→
P.411
“Certificate is rejected (tampered)”
●
This is displayed when an altered SSL certificate has
been received. An SSL communication cannot be
established with this site.
“Certificate is rejected (tampered)”
●
This is displayed when an altered SSL/TLS certificate
has been received. An SSL/TLS communication cannot
be established with this site.
“Channel is not searched”
●
Available channels could not be found.
“Character count exceeded. Delete text to an
allowable size”
●
The combined double-byte character count for the main
text and quotation symbols in a reply-with-quote i-mode
mail exceeds 5,000 characters. Delete text to bring the
count to 5,000 double-byte characters or less.
“Check new messages is set all OFF”
●
New messages cannot be checked because none of
the items is selected in “Set check new messages”.
Select items to check in “Set check new messages”.
→ P.152
“Connection failed (403)”
●
Connection to the site failed for some reason. Retry
connection.
“Connection failed”
●
This is displayed when the host settings are incorrect.
Set the host correctly, using “Host selection” under
Connection setting.
→ P.179
●
Connection to i-mode failed for some reason. Retry
connection.
“Connection failed”
●
Set “Caller ID Notification” to “ON” and retry. → P.44
“Connection interrupted”
●
i-mode connection was interrupted due to poor
reception. Move to a location where the reception is
good before using the i-mode service.
→ P.42
●
If this message appears when the signal is strong and
the “
” mark is displayed, the connected site is very
busy. Retry later.
“Continue using the i-
α
ppli and communication?”
●
This is displayed when you selected “NO” or “Terminate
i-
α
ppli” in response to “The number of i-
α
ppli
communications is large. Continue communication?”
Select “YES” to continue i-
α
ppli communication. Select
“Terminate i-
α
ppli” to stop using the i-
α
ppli.
“Could not read”
●
Copying could not be completed, for some reason.
Replace with a different microSD memory card and try
to copy again.
“Could not start because of a different FOMA
card (UIM)”
●
This is displayed when an i-
α
ppli that is restricted by
FOMA card security function attempted to start
automatically.
→ P.36
“Could not start the specified software because
of a different FOMA card (UIM)”
●
This is displayed when you specify and attempt to start
an i-
α
ppli that is restricted by FOMA card security
function. → P.36
“Current UIM is not registered as IC owner Unable
to download”
“Current UIM is not registered as IC owner Unable
to move”
“Current UIM is not registered as IC owner Unable
to run”
“Current UIM is not registered as IC owner Unable
to delete”
“Current UIM is not registered as IC owner Unable
to upgrade”
●
This is displayed when you tried to operate an Osaifu
Keitai-related i-
α
ppli or tried to move an i-
α
ppli from a
microSD memory card when the inserted FOMA card
and FOMA card information stored for FeliCa are
different.
“Data is too long A part is deleted”
●
The size of address, subject or text or more than one
data exceeds the maximum, and the Compose
message screen appears with the excess part deleted.
“Data transmission is frequent Press CLR and
confirm data transmission”
●
This is displayed when the number of communications
from an i-
α
ppli standby screen becomes very large
within a certain period. Press
t
to select whether or
not to permit communications from the i-
α
ppli standby
display, or to close the i-
α
ppli standby display.
→
P.251
“Dial/Receive calls activating Original lock”
●
This is displayed when you have attempted a prohibited
operation while the original lock is applied to “Dial/
sending mail” and to “Incoming/Mail disp.”.
→
P.115
“Download failed”
●
This is displayed when a download of a melody, Chara-
den or download dictionary suffered a communication
error or improper data.