10
Use
2
Use
.
2.1
Before use
1.
Unpack the appliance and all its accesso-
ries.
2.
Check the contents for completeness and
possible damages. For the scope of deliv-
ery, see fig. 1.
3.
Insert the end of the suction hose into the
intake opening (Fig. 2/A) until the catch
(Fig. 2/A/1) clicks into place. Make sure
that the catch (Fig. 2/A/1) is on the upper
side.
4.
Insert the handle into the upper end of the
telescopic tube (Fig. 2/B).
5.
Attach the floor nozzle to the bottom end of
the telescopic tube (Fig. 3/A).
6.
Adjust the length of the telescopic tube.
Press down the release catch on the tele-
scopic tube to do this (Fig. 3/B). Then ex-
tend the telescopic tube to the desired
length. Let go of the release catch while
pulling until it locks in place. You will hear a
distinct click.
7.
Attach the supplied accessory nozzles to
the accessory holder (Fig. 4). If you put the
furniture brush (Fig. 4/1) onto to the crevice
nozzle (Fig. 4/2), the twin holders can take
3 accessory nozzles.
2.2
Vacuum cleaning
1.
Attach the desired nozzle to the telescopic
tube (Fig. 5/1) or directly to the handle
(Fig. 5/2).
2.
If using the floor nozzle, set the "carpet/
hard floor" selector (Fig. 6) according to the
type of floor to be cleaned:
for short- and deep-pile carpets,
rugs, etc. (Fig. 6/A);
for hard floors such as laminate,
tiles, PVC etc. (Fig. 6/B).
3.
Pull out the power cord by the plug up to the
yellow mark.
4.
Insert the mains plug into a socket with
ground/safety contact.
5.
Switch on the vacuum cleaner with the on/
off switch (Fig. 8/1).
6.
With the suction power control (Fig. 7/A),
set the suction power to suit the surface to
be cleaned.
- By sliding it towards the cable retraction
button (Fig. 8/2), you can increase suc-
tion power to pick up deeply imbedded
particles in carpets, runners, crevices,
etc.
- By pushing it towards the on/off switch
(Fig. 8/1) you can reduce power, e.g. for
gentle cleaning of curtains.
2.3
Switching off
1.
Switch off the vacuum cleaner with the on/
off switch (Fig. 8/1) and pull the plug from
the mains socket.
2.
Keep the plug in your hand.
3.
Push the cord retracting button (Fig. 8/2) to
retract the power cord.
2
3
4
5
6
7
8
ATTENTION:
Always transport or ship the appliance in its
original packaging to avoid damage. Keep
the packaging for such an event.
Dispose of no longer needed packaging
material properly.
NOTE:
Immediately contact your dealer if you have
found damage resulting from transportation.
WARNING:
Danger of injury! A damaged appliance must
not be used. Check the vacuum cleaner and
the power cord for damages before each
use.
ATTENTION:
Only use the vacuum cleaner with all filters
intact, in dry condition and correctly placed.
Make sure that the openings of the vacuum
cleaner are not clogged.or obstructed.
WARNING:
Danger of injury! Especially when vacuum-
cleaning stairs, always take care that you are
standing above the appliance .
ATTENTION:
Before vacuuming make sure that the
attached nozzle and the set suction power
suit the surface to cleaned. Please follow the
flooring manufacturer's recommendations.
WARNING:
Danger of electric shock! If the red marking
shows retract the cord by pressing the
retraction button (Fig. 8/2) to pull in the cable
up to the yellow mark again. Otherwise the
power cord might break.
NOTE:
With the bypass vent (Fig. 7/B) you can
quickly reduce the suction power if less
power is needed, e.g. to release curtains
accidentally sucked in.
WARNING:
Danger of injury! During uncontrolled retrac-
tion the power cord can whip around,
become an obstacle or overthrow objects.
Therefore keep the plug in your hand and
guide it during retraction of the power cord.
M3.book Seite 10 Dienstag, 29. März 2011 8:24 08
Содержание Centrino M3
Страница 3: ...3 1...
