Digital Equipment PRIORIS MTE Скачать руководство пользователя страница 9

Страница: 9 / 73

Digital PRIORIS MTE Server

Product Description

MCS Logistics Engineering - Nijmegen

P
R

T
E

Chapter 1

Product Description

Product Introduction

The Prioris MTE servers are a family of high-performance, i486 processor-based, personal computers equipped
with the latest microprocessor technology. They can be used as stand-alone computers, as clients, or as servers
in a network environment.

Features

♦

Upgradable system comptible P24T ZIF socket

♦

8 MB system RAM, Upgradable to 128 MB on motherboard

♦

128 KB external cache memory (direct-mapped), expandable to 256 KB

♦

On-board IDE controller

♦

SVGA video card, 1 MB, ISA included

♦

Supports up to five storage devices

♦

Five full-size, 32 bit EISA slots and one slot which is either a VL-bus VESA slot or an EISA slot (for a
maximum of six EISA slots)

♦

Interfaces: two serial (RS-3232C) and one parallel (Centronics)

♦

Autosensing Power supply, 260 Watt

Содержание PRIORIS MTE










































































Результаты поиска

Содержание PRIORIS MTE

Отзывы:

Похожие инструкции для PRIORIS MTE

Бренды по названию

Популярные бренды

Digital Equipment PRIORIS MTE, Руководство по техническому обслуживанию

Результаты поиска

Содержание PRIORIS MTE

Отзывы:

Похожие инструкции для PRIORIS MTE

Бренды по названию

Популярные бренды