Digital Equipment PRIORIS MTE Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 73

Digital Equipment PRIORIS MTE Скачать руководство пользователя страница 20

Server Utilities & configuration

Digital PRIORIS MTE Server

20

MCS Logistics Engineering - Nijmegen

P
R

I

O

R

I

S

M

T
E

SCU and Setup Options

(continued)

Menu Fields

Settings

Comments

Boot from
Hard Disk
Drive C

Enabled
Disabled

Enables IDE drive C as a logical boot device.
Disables IDE drive C as a logical boot device.

Serial Port 1
Serial Port 2

Enabled at
COM1, COM2,
COM3, COM4
Disabled

Enables any desired on-board serial port.

Disables any desired on-board serial port at the specified base address.

Parallel Port

Enabled at base
address 378h,
278h, 3BCh
(compatible)
Disabled

Enables on-board printer port.

Disables any desired on-board printer port.

Video Type

VGA or EGA
CGA 40
columns
CGA 80
columns
Monochrome

Allows to specify the type and mode of the video module that is installed.

Shadow Video
BIOS ROM

Enabled

Disabled

Enables the shadowing request for Video BIOS ROM. When shadowing
of this area is enabled, caching is also enabled.
Disables the shadowing request for Video BIOS ROM.

Shadow
C8000h-
CFFFFh
Shadow
D0000h-
D7FFFh
Shadow
D8000h-
DFFFFh

Enabled
Disabled

Disables the shadowing request for optional ROM.
Enables the shadowing request for optional ROM.

Primary
Cache Control

Enabled

Disabled

Enables the microprocessor's internal (primary) cache. Enabling the
cache controller significantly improves computer performance by
reducing the average number of wait states seen by the microprocessor.
Disables the microprocessor's internal cache.

«
...
18
19
20
21
22
...
»

Содержание PRIORIS MTE










































































Отзывы:

Нет отзывов