Delta Controls eZFC-424R4-24 Скачать руководство пользователя страница 64

Страница: 64 / 85

eZFC-424R4-24 Application Guide
Edition 2.6

Page 63 of 84

If the system uses a multi-speed fan, the minimum fan speed that the fan can run at is its

lowest speed.

If the system uses an ECM fan, the minimum fan speed that the ECM fan will run at is its

stated minimum speed.

When there is no heat/cooling demand for the fan, the fan (when set to run intermittently) will run

for a certain time (FanDelayOffTime AV143) before it turns off completely.

Fan Stages

The algorithm supports up to 3 fan stages for binary fans (multi-speed) and analog fans (ECM).

The fan must be running for duct heating or cooling to be active.

Heating and cooling demands are determined by the HeatCoolLoad (AV802) object. Heating load

is present when the HeatCoolLoad value is between 0 and 100. Cooling load is present when the

HeatCoolLoad value is between 0 and -100. The algorithm divides the overall heating or cooling

load equally between all heating or cooling stages.

Stage load is the portion of the HeatCoolLoad that is dedicated to a particular stage of heating or

cooling.

In the configuration graphic, a fan stage can be associated with a single or multiple heat or cooling

stages, or multiple fan stages can be associated with a single heat or cooling stage.

Single Speed Fans

The following table describes the

duct fan stage

behavior for a fan with intermittent fan mode

setting. A fan set at constant fan mode is always running.

Heat/

Cooling

Stage

Occupied Mode

Unoccupied Mode

Binary

Fan turns on when there is a duct heating or

cooling demand. Turns off when duct heating or

cooling demand is 25% to reduce overshoot.

Fan turns on at 100% overall

load and turns off when the

demand drops down to 25%.

Analog

Fan turns on at 25% stage load and stays on.

Fan turns off when demand drops to 0%.

Fan turns on at 100% overall

load and turns off when the

demand drops down to 0%.

Содержание eZFC-424R4-24






















































































Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды

Delta Controls eZFC-424R4-24, Инструкция по применению

Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды