Delta Controls eZFC-424R4-24 Скачать руководство пользователя страница 54

Страница: 54 / 85

eZFC-424R4-24 Application Guide
Edition 2.6

Page 53 of 84

Controllers Tab

What is the Controllers Tab?

Use the Controllers tab on the enteliZONE controller configuration page to fine tune the controller's

control feedback algorithm.

This section defines each field on the controller tab.

Controller Type

The control algorithm used by the controller. The algorithms are PI (Proportional-Integral), P

(Proportional), PID (Proportional-Integral Derivative) and I (Integral).

Proportional Band

The temperature range which the input must vary to cause a change in the controller output from 0

to 100%.

Deadband

The controller deadband is a small range in which temperature variation is allowed. When the input

is within the deadband, the controller output is fixed.

Deadbands should be small enough so that the occupant does not notice the temperature

variations within the deadband. However, making deadband ranges too small will make the

actuators adjust frequently and cause unnecessary wear on the equipment.

Integral Rate

The integral rate is defined as the amount of bias change per minute. It is expressed as percentage

change per minute.

The integral rate determines how fast the controller bias is adjusted to make the necessary

correction so that there is no offset between the signal and the setpoint.

Reset Band

The reset band provides a dynamic means to adjust the amount of output bias added to the

controller output.

When the input is outside of the reset band, the effective reset rate is equal to the specified reset

rate. When the input is within the reset band, the effective reset rate is proportionally reduced.

When the input is within the deadband, no further reset action occurs.

Содержание eZFC-424R4-24






















































































Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды

Delta Controls eZFC-424R4-24, Инструкция по применению

Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды