Dell PowerEdge UPS 500T Скачать руководство пользователя страница 99

Страница: 99 / 134

Event Descriptions

Self-Test Canceled

Information

Self-Test Ended

Information

Specific Date Self-Test Started Information

Specific Date Self-Test

Canceled

Information

Specific Date Self-Test Ended Information

Monthly Self-Test Started

Information

Monthly Self-Test Canceled

Information

Monthly Self-Test Ended

Information

UPS Control Power ON

none

On Manual Bypass

Alarm only

Applies to 5600W and double-

conversion UPS models only.

In High Efficiency Mode

none

Applies to double-conversion UPS

models only.

ON Buck / Input Voltage

Reducer

none

ON Boost / Input Voltage

Booster

none

ABM State Charging

none

ABM State Floating

none

ABM State Resting

none

ABM State OFF

none

Clock Set Done

none

To Bypass Command

none

Applies to 5600W and double-

conversion UPS models only.

From Bypass Command

none

Applies to 5600W and double-

conversion UPS models only.

UPS On Command

none

UPS Off Command

none

Battery Disconnected

Alarm only

Shutdown Imminent

Alarm only

Service Battery

Alarm and disables battery

charging (ABM in Charger Off

mode)

Number

Event Description

Type of Message

Remarks

Содержание PowerEdge UPS 500T







































































































































Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды

Dell PowerEdge UPS 500T, Руководство по установке и настройке

Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды