Dell PowerEdge UPS 500T Скачать руководство пользователя страница 115

Страница: 115 / 134

Installation on a VMware ESX Server

115

Enter the shutdown commands (see Figure 116).
Example:

shutsys -ip 172.18.127.47 -e true
shutbackup -ip 172.18.127.47 -e true -m 1:00
shutfile -e true -f shutdown -m 2
listshut -ip 172.18.127.47

NOTE:

See “Dell CUI Commands List” on page 132 for a description of all Dell CUI commands.

NOTE:

Each guest operating system requires a minimum of 30 seconds to run the command file before shutdown.

The -m 1 option in the shutfile command in the example below sets one minute as the total time allowed to run the

command file before shutdown, which allows sufficient time for two guest operating systems.

Example: shutfile -e true -f shutdown.sh -m 1

The host and guest operating system shut down orderly and gracefully after the battery discharges for

one minute.

Figure 116. Shutdown Parameters

NOTE:

The VMware ESX and ESXi Server Scripts are from William Lam, VMware vExpert.

http://communities.vmware.com/docs/DOC-9531

Thanks to William Lam (@lamw on Twitter and VMTN) for use of the Scripts.

Содержание PowerEdge UPS 500T







































































































































Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды

Dell PowerEdge UPS 500T, Руководство по установке и настройке

Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды