Dell PowerEdge UPS 500T Скачать руководство пользователя страница 63

Страница: 63 / 134

Configuring the Software

Remote Shutdown by Agent

To configure for shutdown by a remote Agent:

Select the R

emote Shutdown by Agent

check box and click

Add

Enter the IP address (IPv4 address or IPv6 address) or host name of the Agent.

Click

to save and exit.

When the local Agent receives the specified Agent's shutdown signal, the system shuts down in the

specified delay time.

Run Command File before Shutdown

Before system shutdown, the Agent can initiate a command if this

parameter is not zero. The Agent does not begin to shut down the

system until the ”Execute file before system shutting down” ends.

Shutdown File Max Execution Time

Before system shutdown, the time required to implement the

shutdown file.

Shutdown Conditions

Displays the remote Agents to be shut down. You can add, modify, or

remove the remote Agents.

Shutdown Alarm Interval

The number of minutes between each shutdown warning.

Start Warning before Scheduled Shutdown

The time in minutes before a scheduled shutdown when the Agent

issues the first warning.

Parameter

Description

Содержание PowerEdge UPS 500T







































































































































Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды

Dell PowerEdge UPS 500T, Руководство по установке и настройке

Результаты поиска

Содержание PowerEdge UPS 500T

Отзывы:

Похожие инструкции для PowerEdge UPS 500T

Бренды по названию

Популярные бренды