Dell PowerEdge 860 Скачать руководство пользователя страница 92

Страница: 92 / 140

Troubleshooting Your System

Run the appropriate online diagnostic test.

If the tests fail, see "Getting Help" on page 103.

For each expansion card you removed in step 9, perform the following steps:

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Open the system. See "Opening the System" on page 46.

Reinstall one of the expansion cards.

Close the system. See "Closing the System" on page 47.

Run the appropriate diagnostic test.

If the tests fail, see "Getting Help" on page 103.

Troubleshooting the Microprocessor

Problem

•

Error message indicates a microprocessor problem.

•

A heat sink is not installed for the processor.

Action

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

Run the appropriate online diagnostics test. See "Using Dell PowerEdge Diagnostics" on page 93.

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Open the system. See "Opening the System" on page 46.

Ensure that the processor and heat sink are properly installed. See "Replacing the Processor" on
page 71.

Close the system. See "Closing the System" on page 47.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

If the problem persists, see "Getting Help" on page 103.

Содержание PowerEdge 860













































































































































Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды

Dell PowerEdge 860, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды