Dell PowerEdge 860 Скачать руководство пользователя страница 85

Страница: 85 / 140

Troubleshooting Your System

Let the system dry thoroughly for at least 24 hours.

Close the system. See "Closing the System" on page 47.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

If the system does not start properly, see "Getting Help" on page 103.

If the system starts properly, shut down the system and reinstall all of the expansion cards that you
removed. See "Installing an Expansion Card" on page 63.

Run the appropriate online diagnostic test. See "Using Dell PowerEdge Diagnostics" on page 93.

If the tests fail, see "Getting Help" on page 103.

Troubleshooting a Damaged System

Problem

•

System was dropped or damaged.

Action

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

Open the system. See "Opening the System" on page 46.

Ensure that the following components are properly installed:

•

Expansion cards

•

Power supplies

•

Fans

Ensure that all cables are properly connected.

Close the system. See "Closing the System" on page 47.

Run the system board tests in the system diagnostics. See "Running the System Diagnostics" on
page 93.

If the tests fail, see "Getting Help" on page 103.

Содержание PowerEdge 860













































































































































Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды

Dell PowerEdge 860, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды