Dell PowerEdge 860 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 140

background image

52

Installing System Components

Configuring the Boot Drive

The drive or device from which the system boots is determined by the boot order specified in the System
Setup program. See "Using the System Setup Program" on page 29. To boot the system from a hard drive
or drive array, the drive(s) must be connected to the appropriate controller:

•

For systems using the integrated hard-drive controller, the master drive (drive 0) must be connected to
the SATA_PORT_0 connector on the system board. To identify system board connectors, see
Figure 6-2.

•

For systems with a SAS controller installed, the hard drive must be connected to the SAS controller
card. See the documentation that accompanied the controller card.

•

To boot from a SAS RAID array, the drive must be connected to the RAID controller card. See the
documentation that accompanied the controller card.

Hard Drives

Your system contains up to two non-hot-pluggable SATA or SAS hard drives. If your system contains SAS
hard drives, they must be connected to a SAS controller card. The cables for hard drive 1 are routed
through a cable clamp mounted to the chassis.

Removing a Hard Drive

The procedures for removing and installing SATA or SAS hard drives are the same.

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

1

Open the system. See "Opening the System" on page 46.

2

If applicable, remove the optical drive.

Remove the optical drive if you are removing hard drive 0. See "Removing the Optical Drive" on
page 50.

3

Disconnect the power and interface cables from the hard drive.

The interface cables for SATA hard drives are connected to the system board. See Figure 6-2 for the
location of the system board connectors.

The interface cables for SAS hard drives are connected to a controller card.

4

Pull up on the plunger that secures the hard-drive carrier to the chassis. See Figure 3-7.

5

Slide the hard-drive carrier backward and lift the carrier out of the chassis.

«
...
50
51
52
53
54
...
»

Содержание PowerEdge 860













































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 860

Бренд: Jetter Страницы: 35

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: Opengear Страницы: 2

LinkStation Mini

Бренд: Buffalo Страницы: 71

Бренд: AOpen Страницы: 18

RocketCache 3240X8

Бренд: HighPoint Страницы: 17

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

See3CAM 30 Z10X

Бренд: e-con Systems Страницы: 14

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: ENERMAX Страницы: 33

Бренд: Renesas Страницы: 67

Бренд: Renesas Страницы: 6

Soundweb 9088ii DSP System

Бренд: BSS Audio Страницы: 2

Бренд: Epson Страницы: 19

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды