Dell PowerEdge 860 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 140

background image

20

About Your System

Primary drive 0/1 failure

Faulty drive. INT13 call failure from
the drive.

Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.

Read fault

Requested sector not found

The operating system cannot read
from the diskette or hard drive, the
system could not find a particular
sector on the disk, or the requested
sector is defective.

Replace the diskette. Ensure that the
diskette and hard-drive cables are
properly connected. See
"Troubleshooting a USB Device" on
page 83, "Troubleshooting a Hard Drive"
on page 90, or "Troubleshooting a Hard
Drive" on page 90 for the appropriate
drive(s) installed in your system.

Remote Configuration

update attempt failed

System could not implement Remote
Configuration request.

Retry Remote Configuration.

ROM bad checksum =

address

Faulty or improperly installed
expansion card.

Remove and reseat the expansion cards.
See "Troubleshooting Expansion Cards"
on page 91.

SATA port 0/1 hard disk

drive configuration error

Faulty drive. Parameters failure.

Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.

SATA port 0/1 hard disk

drive failure

SATA port 0/1 hard disk

drive auto-sensing error

Faulty drive. INT13 call failure from
the drive.

Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.

SATA Port 0/1 hard disk not

found

SATA Port0/1 set as Auto, no disk
installed.

Run the System Setup program to
correct the settings. See "Using the
System Setup Program" on page 29.

Sector not found

Seek error

Seek operation failed

Faulty diskette or hard drive.

See "Troubleshooting a USB Device" on
page 83, "Troubleshooting a Hard Drive"
on page 90, or "Troubleshooting a Hard
Drive" on page 90 for the appropriate
drive installed in your system.

Shutdown failure

Shutdown test failure.

Ensure that all memory modules are
properly installed. See "Troubleshooting
System Memory" on page 88. If the
problem persists, see "Getting Help" on
page 103.

Table 1-4.

System Messages

(continued)

Message

Causes

Corrective Actions

«
...
18
19
20
21
22
...
»

Содержание PowerEdge 860













































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 860

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 5

Бренд: MEDIATEK Страницы: 166

Бренд: Intel Страницы: 958

Бренд: Cypress Semiconductor Страницы: 38

Бренд: PairGain Страницы: 48

Бренд: Renesas Страницы: 21

Бренд: WiebeTech Страницы: 8

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

Бренд: Xtreme Страницы: 83

Embedded Intelligent Module SX-560

Бренд: Silex technology Страницы: 110

Бренд: Transition Networks Страницы: 5

Бренд: Idex Страницы: 4

Бренд: NetApp Страницы: 28

Бренд: Korg Страницы: 8

MPG SEKIRA 500X

Бренд: MSI Страницы: 2

MPG CORELIQUID K240

Бренд: MSI Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды