Dell PowerEdge 860 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 140

background image

Installing System Components

77

5

Connect the two power cables to the 12V and PWR_CONN connectors on the system board. See
Figure 6-2.

6

Connect the chassis intrusion cable to the INTRUSION_SWITCH connector on the system board.

7

Install the riser card. See "Installing the Riser Card" on page 67.

8

Using a #2 Phillips screwdriver, tighten the two screws that secure the riser card to the system board.

9

Install any PCI expansion cards that you removed. See "Installing an Expansion Card" on page 63.

10

Connect the hard-drive interface cables:

a

If you installed a SAS controller, reconnect the interface cable to the controller card.

b

If your configuration uses the integrated controller, reconnect the hard drive 0 interface cable to
the SATA_0 connector and the hard drive 1 interface cable to the SATA_1 connector on the
system board. See Figure 6-2 for the location of the SATA connectors.

11

Install the processor and heat sink. See "Replacing the Processor" on page 71.

12

Install the memory modules. See "Installing Memory Modules" on page 69.

NOTE:

Install the memory modules as noted in step 3 of the procedure in "Removing the System Board

Assembly" on page 75.

13

Connect the control-panel interface cable to the FP_CONN1 connector on the system board. See
Figure 6-2 for the location of the FP_CONN1 connector.

14

If applicable, connect the optical drive interface cable to the IDE connector on the system card. See
Figure 6-2 for the location of the IDE connector.

15

Install the cooling shroud. See "Installing the Cooling Shroud" on page 48.

16

Close the system. See "Closing the System" on page 47.

«
...
75
76
77
78
79
...
»

Содержание PowerEdge 860













































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 860

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: GE Страницы: 146

Бренд: Datasat Страницы: 170

Бренд: Ebyte Страницы: 14

Бренд: Commell Страницы: 36

Бренд: Pressalit Care Страницы: 31

Бренд: Cypress Semiconductor Страницы: 19

Бренд: Softing Страницы: 16

Бренд: Dave Embedded Systems Страницы: 79

Бренд: Digisol Страницы: 73

SteelCentral NetExpress 470

Бренд: Riverbed Страницы: 140

Бренд: Freescale Semiconductor Страницы: 42

METERS AND MORE UM2241

Бренд: ST Страницы: 26

Бренд: Infoblox Страницы: 44

Бренд: Wavtech Страницы: 8

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

Бренд: INGENIA Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды