Dell PowerEdge 860 Скачать руководство пользователя страница 61

Страница: 61 / 140

Installing System Components

Connect the control panel interface cable to the FP_CONN1 connector on the system board. See
Figure 6-2 for the location of the connector.

Connect the optical drive interface cable to the IDE connector on the system board. See Figure 6-2 for
the location of the connector.

Close the system. See "Closing the System" on page 47.

Power Supply

The system supports a single nonredundant power supply.

Removing the Power Supply

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

Open the system. See "Opening the System" on page 46.

Disconnect the following power supply cables:

P3 from the hard drive cable harness

P2 from system board connector 12V

P1 from system board connector PWR_CONN

Using a #2 Phillips screwdriver, remove the screw at the front of the power supply that secures the
power supply to the chassis. See Figure 3-13.

Slide the power supply forward and lift straight up to remove the power supply from the chassis.

Содержание PowerEdge 860













































































































































Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды

Dell PowerEdge 860, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды