Dell PowerEdge 860 Скачать руководство пользователя страница 51

Страница: 51 / 140

Installing System Components

Figure 3-6.

Removing and Installing the Optional Optical Drive

Installing the Optical Drive

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

Align the optical drive's mounting holes with the retaining pins on the hard drive 0 bracket. See
Figure 3-6.

Rotate the drive downward until it snaps into place.

Connect the interposer card to the optical drive.

Push the plungers into the captive fastener barrels until they snap into place.

Connect the interface and power cables to the optical drive's interposer card.

Close the system. See "Closing the System" on page 47.

interposer board

captive fasteners (2)

interface cable

retaining pins (4)

mounting holes (4)

bracket release lever

hard drive 0

Содержание PowerEdge 860













































































































































Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды

Dell PowerEdge 860, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge 860

Отзывы:

Похожие инструкции для PowerEdge 860

Бренды по названию

Популярные бренды