Dell PowerEdge 860 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 140

background image

16

About Your System

Table 1-4.

System Messages

Message

Causes

Corrective Actions

Amount of available memory

limited to 256MB

The

OS Install Mode

option in the

System Setup program is set to

On

.

This limits the amount of available
memory to 256 MB because some
operating systems will not complete
installation with more than 2 GB of
system memory.

After the operating system is installed,
enter the System Setup program and set
the

OS Install Mode

option to

Off

. See

your

Hardware Owner’s Manual

for

details.

Attempting to update

Remote Configuration.

Please wait....

Remote Configuration is in progress.

Wait until the process is complete.

BIOS Update Attempt

Failed!

Remote BIOS update attempt failed. Retry the BIOS update. If the problem

persists, see "Getting Help" on page 103.

Caution! NVRAM_CLR jumper

is installed on system

board.

NVRAM_CLR jumper is installed.

Check the System Setup configuration
settings. See

"Using the System Setup

Program

" on page 29. Remove the

NVRAM_CLR jumper. See Figure 6-1
for jumper locations.

Data error

The diskette drive or hard drive
cannot read the data.

For the operating system, run the
appropriate utility to check the file
structure of the diskette drive or hard
drive.

See your operating system
documentation for information on
running these utilities.

Decreasing available

memory

One or more memory modules might
be improperly seated or faulty.

Reinstall the memory modules and, if
necessary, replace them. See "System
Memory" on page 67.

See "Troubleshooting System Memory"
on page 88.

Diskette read failure

Faulty or improperly inserted diskette. Replace the diskette.

Diskette subsystem reset

failed

Faulty diskette drive or optical drive
controller.

Ensure that the diskette drive and
optical drive cables are properly
connected. See "Troubleshooting a USB
Device" on page 83 and
"Troubleshooting an Optical Drive" on
page 89. If the problem persists, see
"Getting Help" on page 103.

Drive not ready

Diskette missing or improperly
inserted in diskette drive.

Reinsert or replace the diskette.

«
...
14
15
16
17
18
...
»

Содержание PowerEdge 860













































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 860

Univerge SV8100

Бренд: NEC Страницы: 44

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

Бренд: Cabletron Systems Страницы: 54

Cabletron BRIM-F6

Бренд: Cabletron Systems Страницы: 43

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 60

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: ICP DAS USA Страницы: 48

Бренд: ICP DAS USA Страницы: 24

Бренд: Keithley Страницы: 59

Бренд: DAQ system Страницы: 41

Бренд: DAQ system Страницы: 19

Бренд: Rolls Страницы: 2

eBOX532-100-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Zoom Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды