DATREND Systems Oxitest Plus 7 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 62

background image

Warranty Disclaimer

Should you elect to have your instrument serviced and/or calibrated by someone other than Datrend
Systems, please be advised that the original warranty covering your product becomes void when the
tamper-resistant Quality Seal is removed or broken without proper factory authorization. We strongly
recommend, therefore, that you send your instrument to Datrend Systems for service and calibration,
especially during the original warranty period.

In all cases, breaking the tamper-resistant Quality Seal should be avoided at all cost, as this seal is the
key to your original instrument warranty. In the event that the seal must be broken to gain internal
access to the instrument (e.g., in the case of a customer-installed firmware upgrade), you must first
contact Datrend Systems at 1-800-667-6557. You will be required to provide us with the serial number
for your instrument as well as a valid reason for breaking the Quality Seal. You should break this seal
only after you have received factory authorization. Do not break the Quality Seal before you have
contacted us! Following these steps will help ensure that you will retain the original warranty on your
instrument without interruption.

WARNING

Unauthorized user modifications or application beyond the published specifications may result in
electrical shock hazards or improper operation. Datrend Systems will not be responsible for any injuries
sustained due to unauthorized equipment modifications.

DSI DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR
APPLICATION.

THIS  PRODUCT  CONTAINS  NO  USER-
SERVICEABLE COMPONENTS.  UNAUTHORIZED
REMOVAL OF THE  INSTRUMENT COVER SHALL
VOID  THIS  AND  ALL  OTHER  EXPRESSED  OR
IMPLIED WARRANTIES.

«
...
5
6
7
8
9
...
»

Содержание Oxitest Plus 7































































Отзывы:

Нет отзывов

Похожие инструкции для Oxitest Plus 7

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: Fisher Scientific Страницы: 42

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: XanLite Страницы: 4

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Sonorex Super RK 31

Бренд: BANDELIN Страницы: 21

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренд: B.Pro Страницы: 48

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды