DATREND Systems Oxitest Plus 7 Скачать руководство пользователя страница 32

Страница: 32 / 62

OXITEST PLUS 7 OPERATING MANUAL

3.12 Saving and Printing Test Results

Up to 20 PASS/FAIL results from manually-conducted tests may be saved in the memory of

Oxitest Plus 7

for later printout or downloading to a personal computer (PC). In addition to the 20

manual test results,

Oxitest Plus 7

can also save the results of Auto Preset tests and Alarm Tests.

Manual test and Auto Preset test results are saved to

Oxitest Plus 7

memory by pressing either the

Pass

Fail

key on the front panel keypad. The information saved includes the test SpO

, heart

rate, pulse amplitude and motion artifact settings, plus the PASS or FAIL status of the test and the
oximeter signal status displayed at the upper right corner of the

Oxitest Plus 7

LCD. The oximeter

signal status is saved in abbreviated format as follows: OK = “RED+IR OK”; NoRD = “No Red”;
NoIR = “ No IR”; and ?? = “NO SIGNAL” or “Testing”.

For each Alarm Test performed, the oximeter ALARM-ON and ALARM-OFF times are
automatically saved in the

Oxitest Plus 7

memory if the Alarm Test is run through to completion.

There is no need to press

Pass

Fail

to save the results of an Alarm Test.

All test results saved in the

Oxitest Plus 7

memory are retained by battery back-up when the power

is switched off. This allows test results to be acquired over a period of time and then printed out or
downloaded later.

Pressing the

Print

key causes the test results saved in the memory to be transmitted from the

Oxitest Plus 7

RS-232 Port as a formatted “Test Report”. The

Oxitest Plus 7

RS-232 Port may

be connected to a Citizen iDP-3110 serial printer or to a personal computer. Refer to section 4.2 for
the interconnection cable details.

The format of the Test Report is similar to the following example printout:

Operation/Chapter 3

Page 22

Содержание Oxitest Plus 7































































Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды

DATREND Systems Oxitest Plus 7, Руководство по эксплуатации

Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды