DATREND Systems Oxitest Plus 7 Скачать руководство пользователя страница 27

Страница: 27 / 62

OXITEST PLUS 7 OPERATING MANUAL

oximeter can be powered up

after

applying the sensor to

Oxitest Plus 7

. Positioning the sensor

properly may be more difficult for short, stubby sensors. Section 5.1.2 offers some advice on how
to position some specific types of sensors.

3.9

Selecting Motion Artifact Simulation

Oxitest Plus 7

provides four waveforms for simulating various motion artifact conditions. The

wave

adds low frequency noise to the normal patient signal, simulating slow, whole-body

movements. The

SP wave

adds sharp noise spikes to the patient signal, simulating the oximeter

sensor being struck or tapped at random times. The

TR wave

simulates patient tremor or shivering.

The

Sn wave

is a high-amplitude 2.5 Hertz sinewave interference, simulating a "shake table"

laboratory test of a pulse oximeter, as described by Barker et al in "The effects of motion on the
performance of pulse oximeters in volunteers",

Anesthesiology

, 1997; 86:101-8.

The motion artifact simulation is activated by pressing the

Heart Rate

and

Pulse Amp

keys

simultaneously. In response to this key combination, the

Oxitest Plus 7

will emit a double-beep

and activate the MV wave, as indicated by the "

" characters displayed to the left of the pulse

amplitude on the LCD:

N-200 NO SIGNAL
97% 60 BPM

100%

In manual mode, successive presses of

Heart Rate

with

Pulse Amp

will activate the SP, TR and Sn

waves in turn, indicated on the display as "

", "

", and "

" as for the MV wave above. A fifth

press of

Heart Rate

with

Pulse Amp

will de-activate the motion artifact simulation.

In Auto Preset mode, two of the nine factory default presets include motion artifact simulations.
The Alarm Test Mode also provides one alarm test in which the MV wave is turned on and then off
by the

Start/Stop

key. This allows measurement of the oximeter's alarm response to motion

artifacts.

In manual mode, SpO

, heart rate, and pulse amplitude settings on

Oxitest Plus 7

may be

independently varied while the motion artifact simulation is active.

Stability and accuracy of a pulse oximeter under motion artifact conditions is highly dependent on
the

noise-to-signal ratio

(NSR), that is, the relative strength of the artifact signal to the

uncorrupted patient signal. When motion artifact is activated on

Oxitest Plus 7

, simulated NSR

may be continuously varied by means of the Pulse Amp controls. For example, with the pulse
amplitude set to 20%, the NSR would be 5:1.

Operation/Chapter 3

Page 17

Содержание Oxitest Plus 7































































Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды

DATREND Systems Oxitest Plus 7, Руководство по эксплуатации

Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды