DATREND Systems Oxitest Plus 7 Скачать руководство пользователя страница 37

Страница: 37 / 62

OXITEST PLUS 7 OPERATING MANUAL

3.15 Recharging the Battery

Oxitest Plus 7

is powered by an internal NiCad battery with sufficient capacity to provide

approximately 40 hours of operation. When the

Oxitest Plus 7

is OFF, the battery powers a non-

volatile memory which retains the test settings, the

ENA

able/

DIS

able status of the pulse oximeter

menu, and any

Pass/Fail

test results which may have been saved in memory. Power drain from the

battery in this case is negligible.

When the battery approaches full discharge, the STATUS display as shown in Section 3.8 Status
Indicator, will alternate with a

LO BATTERY

indication. To recharge the battery, plug the

supplied

AC adapter

into a wall outlet and the

Oxitest Plus 7

DC ADAPTOR input (see

Figure 2

Use

only the adaptor supplied with the

Oxitest Plus 7

to recharge the battery.

A full battery

recharge will require approximately 14 hours.

If the

Oxitest Plus 7

battery reaches full discharge during use, the unit will stop operating and the

message shown below will appear on the display. In this case, the

Oxitest Plus 7

should be

powered down and the battery given a full recharge as soon as possible.

*BATTERY DISCHARGED*
Recharge immediately

If the

Oxitest Plus 7

battery is near deep-discharge at power-up, the LCD will remain blank and

the

Low Battery

alarm LED on the front panel will illuminate (see

Figure 3

). The

Oxitest Plus 7

will not be operable in this case and should be powered down and the battery given a full recharge
prior to further use. A battery discharged to this level may require replacement or reconditioning to
ensure optimal portable operation of the unit.

Oxitest Plus 7

may also be powered with the supplied switch-mode AC adapter. Having the

Oxitest Plus 7

powered up will have no effect on the amount of time required to recharge the

battery.

Note:

Older

Oxitest Plus 7

units were supplied with linear AC adapters (refer to Section 1.15 for

replacement part numbers and serial number effectivity). For older model

Oxitest Plus 7

units, recharging the battery while powered up requires somewhat more time than with the
unit powered down.

Unless portable operation is not required, it is not recommended that

Oxitest Plus 7

be connected

to the AC Adapter continuously as this may reduce the life of the battery. The battery will maintain
its capacity longer if

Oxitest Plus 7

is routinely run until LO BATTERY is indicated on the

STATUS display and then fully recharged. All NiCad batteries, however, will degrade over time.

Operation/Chapter 3

Page 27

Содержание Oxitest Plus 7































































Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды

DATREND Systems Oxitest Plus 7, Руководство по эксплуатации

Результаты поиска

Содержание Oxitest Plus 7

Отзывы:

Похожие инструкции для Oxitest Plus 7

Бренды по названию

Популярные бренды