Datatek IP-DSU Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

background image

I P - D S U U s e r ’ s M a n u a l

02/02/08

10

your equipment rack be outfitted with sufficient power strips to accommodate all of the
AC power supplies.

2.5.3 Stand-alone DC Power

The stand-alone

IP-DSU

accepts DC power input directly from a 48V DC power source

and connects into the three position (accepting return, minus and ground power wires)
terminal block labeled “48 VDC” on the faceplate. The terminal-block connectors
accommodate 14 awg to 24 awg (American Wire Gauge) wire. A strain-relief clamp is
available separately for DC wire stabilization.

2.5.4 Rack-mount DC Power

The rack-mount

IP-DSU

accepts DC power input directly from a 48V DC power source

and connects into a main, three position (accepting return, minus and ground power
wires) terminal block labeled “48 VDC” on the rack-mount panel faceplate. Power is
distributed to six terminal blocks vertically below the main terminal block, where each
individual terminal block powers a single

IP-DSU

. Each rack-mount panel accepts two

48V DC power feeds. Twelve

IP-DSU

units can be powered in this manner. The terminal

block connectors accommodate 10awg to 14awg (American Wire Gauge) wire. A strain-
relief clamp is available separately for DC wire stabilization

«
...
8
9
10
11
12
...
»

Содержание IP-DSU

















































Отзывы:

Нет отзывов

Похожие инструкции для IP-DSU

Бренд: ABB Страницы: 44

Бренд: 2N Страницы: 2

Бренд: KE2 Страницы: 16

Бренд: 2Wire Страницы: 14

Бренд: Zero 88 Страницы: 16

Бренд: nedis Страницы: 44

Бренд: Wiznet Страницы: 41

Бренд: QUPIT Страницы: 16

SmartNode 5540E Series

Бренд: Patton Страницы: 77

Бренд: Ascent Communication Technology Страницы: 114

VBG-PN-K20-DMD-EV

Бренд: Pepperl+Fuchs Страницы: 11

Бренд: D-Link Страницы: 153

Бренд: D-Link Страницы: 14

Бренд: ProSoft Technology Страницы: 104

Бренд: Fanvil Страницы: 6

Бренд: Fanvil Страницы: 50

Бренд: Hitron Страницы: 128

CG-ARM7/GTI HS/LS

Бренд: EMS Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды