Datatek IP-DSU Скачать руководство пользователя страница 14

Страница: 14 / 48

I P - D S U U s e r ’ s M a n u a l

02/02/08

Plug one end of the V.35 (requires DB25 to V.35 adapter) or RS232-C device cable into
the

IP-DSU

device interface, and the other end into the existing trunk cable or BNS trunk

I/O board.

Plug the power supply into a standard 115V AC outlet and plug the barrel connector
from the power supply into the circular connector on the

IP-DSU

faceplate labeled “5

VDC”.

3.3.2 DC

ONLY

Attach the provided feet to the bottom of the unit.

Fasten the strain-relief bracket to the side of the

IP-DSU

Place the

IP-DSU

in the desired location, such as a shelf in a data equipment rack.

Plug one end of the RJ45-terminated category 5 twisted-pair data cable into the

IP-DSU

10BaseT LAN interface, and the other into a 10BaseT LAN hub or router.

Plug one end of the RJ45-terminated twisted-pair data cable into the

IP-DSU

console

interface, and the other into the port of the asynchronous device that will be used to
configure or manage the

IP-DSU

Plug one end of the V.35 (requires DB25 to V.35 adapter) or RS232-C device cable into
the

IP-DSU

device interface, and the other end into the existing trunk cable or BNS trunk

I/O board.

Run your 48V DC (return, minus and ground) wires from a central source through the
strain-relief clamp for DC wire stabilization. On the

IP-DSU

faceplate, attach the return,

minus and ground wires to the return, minus and ground connections, respectively, of
the terminal block labeled “48 VDC”.

3.4 Rack-mount

Installation

3.4.1 AC

ONLY

Prepare each

IP-DSU

for rack mounting by attaching the mounting ears to each side of

the unit.

Fasten the twelve-slot rack-mount panel to a 19-inch equipment rack, or use extension
ears for a 23-inch rack. Slide each

IP-DSU

with mounting ears into one of the twelve

rack-mount panel slots. Secure the

IP-DSU

to the rack mount panel with screws.

For each

IP-DSU

, plug one end of the RJ45-terminated category 5 twisted-pair data

cable into the

IP-DSU

10BaseT LAN interface and the other end into a 10BaseT LAN

hub or router.

For each

IP-DSU

, plug one end of the RJ45-terminated twisted-pair data cable into the

IP-DSU

console interface, and the other end into the asynchronous device.

For each

IP-DSU

, plug one end of the V.35 (requires DB25 to V.35 adapter) or RS232-C

device cable into the

IP-DSU

device interface, and the other end into the existing trunk

cable or BNS trunk I/O board.

Содержание IP-DSU

















































Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды

Datatek IP-DSU, Руководство пользователя

Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды