Datatek IP-DSU Скачать руководство пользователя страница 43

Страница: 43 / 48

I P - D S U U s e r ’ s M a n u a l

02/02/08

9 A P P E N D I X A : I P - D S U S P E C I F I C A T I O N S

9.1 Device

Interfaces

9.1.1 CCITT

V.35

The V.35 interface uses a 34-pin connector and operates at data rates up to 2.048Mbps.

9.1.2 EIA

RS-232-C

The RS232-C interface uses a 25-pin (DB25) connector and up to 21 signal leads, and
operates at data rates from 75 to 19200 bits per second (bps).

The

IP-DSU

RS232-C device interface has been tested to run at rates up to 56 Kbps

9.2 10BaseT LAN Interface

This is an eight-pin, 10BaseT modular connector for a 10 Mbps baseband CSMA/CD
local-area network.

9.3 EIA RS-232-C Console Interface

This RS-232-C interface uses an RJ45 connector and operates at 9600 bits per second
(bps).

9.4 Physical

Dimensions

IP-DSU

L=6.0” x W=1.4” x D=7.5”

Rack-mount Panel:

L=19” x W=10.5” D=. 125”

Stand-alone AC/DC Power: L=3.5” x W=1.75” x D=2.5”

Power distribution Panel:

L=10.4” x W=. 8” x D=. 823”

9.5 Environmental Operating Range

Operating Temperature:

5° to 40°C (41°F to 104°F)

Operating Humidity:

5% to 85%

Altitude:

From 60m (197 ft.) below sea level to 1800m (5905 ft.) above sea level

9.6 Power

Requirements

IP-DSU

Operating Voltage:

5V @ 800 mA Nominal

Stand-alone AC power supply:

115V @ 48mA Nominal

115V @ 90 mA Maximum

Содержание IP-DSU

















































Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды

Datatek IP-DSU, Руководство пользователя

Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды