Datatek IP-DSU Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

background image

I P - D S U U s e r ’ s M a n u a l

02/02/08

9

2.3 Console

interface

This interface requires a standard RJ45-terminated twisted-pair data cable. It connects
as data terminating equipment (DTE) to an asynchronous device, and uses RS232-C
signaling. Connection to the

IP-DSU

console is required for initial administration or

StarKeeper® II NMS alarm collection. Otherwise, the console can be disconnected
during normal operation.

1

2.4 Rack-mount

Panel

The

IP-DSU

rack-mount panel contains twelve slots to accommodate that number of

IP-

DSU

units. Each rack-mount panel fits in a 19 or 23 inch EIA standard-equipment rack

(use extension ears when mounting in a 23-inch rack). The rack-mount panel supports 1
inch, 1.75 inch and 2 inch spacing between vertical rail mounting holes. Mounting ears
for

IP-DSU

placements in the rack-mount panel are available.

2.5 Power

Interfaces

Dual power interfaces are present on the

IP-DSU

faceplate. A circular interface labeled

“5 VDC” mates with the barrel connector of a standard wall outlet AC to DC power
transformer for 115V AC installations. A three position (accepting return, minus and
ground power wires) terminal block labeled “48 VDC” is commonly used in central-office
installations.

The

IP-DSU

is factory configured for 115V AC usage. 48V DC operation requires a

different jumper setting on the

IP-DSU

system board.

(

See

Installation

Section

)

2.5.1 Stand-alone AC Power

For this application, a separate AC power supply is available. The power supply has a
six-foot cable that terminates with a barrel connector. The power supply plugs into a
standard 115V AC outlet. The barrel connector plugs into the circular connector labeled
“5 VDC” on the

IP-DSU

faceplate.

2.5.2 Rack-mount AC Power

IP-DSU

rack-mount AC power is the same as in the stand-alone case. This configuration

requires one AC power supply for each

IP-DSU

unit. However, it is recommended that

1

The

IP-DSU

also supports console access through a TCP telnet connection and makes use of the

embedded device standard telnet server port (tcp

1023

). This service is available only when the unit is in

service.

«
...
7
8
9
10
11
...
»

Содержание IP-DSU

















































Отзывы:

Нет отзывов

Похожие инструкции для IP-DSU

Voice Gateway H3C VG 10-10

Бренд: H3C Страницы: 31

SR6602-I AI Series

Бренд: H3C Страницы: 80

SR6602-I AI Series

Бренд: H3C Страницы: 33

SecPath M9000 Series

Бренд: H3C Страницы: 4

SecPath M9000 Series

Бренд: H3C Страницы: 15

MSR3610-I Series

Бренд: H3C Страницы: 5

SecPath M9000 Series

Бренд: H3C Страницы: 57

Бренд: ICP DAS USA Страницы: 96

Бренд: ICP DAS USA Страницы: 38

Бренд: ICP DAS USA Страницы: 17

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 8

Бренд: Billion Страницы: 35

Бренд: TIS Страницы: 5

Бренд: BAB TECHNOLOGIE Страницы: 52

Pathport OCTO 64 Series

Бренд: Pathway connectivity solutions Страницы: 70

Бренд: Pace Страницы: 36

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды