Datatek IP-DSU Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

background image

I P - D S U U s e r ’ s M a n u a l

02/02/08

24

4.4 Local

Syntax: local ipaddr=<IP address> submask=<submask>

The

local

(or

lo

) command sets the address of the

IP-DSU

, to facilitate communication

with a peer

IP-DSU

.

5

The ipaddr is the IP address of this unit. The submask is the subnet mask of this unit,
with a default value of 8 bits (255.255.255.0).

4.5 Destination

Syntax: dest [ipaddr=<IP address>] [trans=< UDP | TCPORIG | TCPRCV >]

The

dest

(or

de

) command specifies the IP address of the peer

IP-DSU

. All data leaving

through the unit’s 10Base-T LAN interface is destined for another

IP-DSU

with this

configured IP address. Address resolution occurs when the unit is restored to service.

By default, UDP is used for data transport. This is the recommended transport protocol.
The

IP-DSU

, using UDP, will minimize delay, optimize throughput, and preserve the

error handling methods of the network. This means that the connected network, whether
it is BNS-2000, SNA, X.25, Frame Relay, or SMDS DXI, will maintain its inherent error
recovery scheme. Re-transmissions (if necessary) will continue to be performed by the
end devices.

The

trans

parameter allows the user to instead select TCP transport. TCP formalizes a

set of rules by which lost data is re-transmitted, and by which out-of-sequence data is
reorganized on a per-byte basis (neither of which is done by UDP). It is typically used for
asynchronous terminal server connections (telnet over TCP). For using TCP, one

IP-

DSU

is considered the call originator and the peer unit is considered the call receiver,

hence the TCPORIG and TCPRCV options. For correct operation, the

IP-DSU

and its

peer must have the opposite options if TCP is being used.

The TCP transport rate should not exceed 56 Kbps., whereas the default UDP transport
option is capable of transmission rates up to T1 (1.544 Mhz).

4.6 Gateway

Syntax: gateway ipaddr=<IP address>

The

gateway

(or

ga

) command specifies the IP address of the local gateway router, if

any. If the remote

IP-DSU

resides on a different LAN, the gateway is the first hop data

travels through to reach it.

5

References to a peer

IP-DSU

include the use of a Universal Trunk Module (UTM) optioned for “IPDSU”

trunk type as the peer.

«
...
22
23
24
25
26
...
»

Содержание IP-DSU

















































Отзывы:

Нет отзывов

Похожие инструкции для IP-DSU

Бренд: S&C Страницы: 9

Бренд: WAGO Страницы: 78

Бренд: FACTBIRD Страницы: 2

INKNXMIT015C000

Бренд: HMS Страницы: 32

Бренд: ZyXEL Communications Страницы: 2

Бренд: QUPIT Страницы: 16

Бренд: ZyXEL Communications Страницы: 18

Бренд: Telco Страницы: 28

Бренд: XAVi Страницы: 51

Бренд: Vaisala Страницы: 32

Бренд: Vaillant Страницы: 40

Бренд: tilgin Страницы: 20

Бренд: tilgin Страницы: 20

Бренд: Planet Networking & Communication Страницы: 235

Бренд: ActionTec Страницы: 89

intelligent Touch Manager BACnet DCM014A51

Бренд: Daikin Страницы: 148

Бренд: 3Com Страницы: 47

OfficeConnect 3C855

Бренд: 3Com Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды